If you have ordered the Argus 2E or if you are interested in this camera model, and want to get some basic information about this product before putting it in use or placing the order, you may refer to the introduction below.

This article includes the following 4 parts which will help you quickly understand the use and working principle of the camera:

Part 1: Unboxing Video 

Part 2: Product Overview

Part 3: Installation 

Part 4: Initial Setup

Unboxing Video of Argus 2E

If you just receive your new camera and are not familiar with the camera, you can have a look at the  video below about unboxing, setup and installation of the camera.

Product Overview

You may find the detailed information about the structure and components of the camera here.

argus-2e-1.png.webp

  1. Daylight Sensor
  2. 6 IR LEDs 
  3. Lens
  4. Status LED
  5. Built-In PIR Motion Sensor
  6. Built-In Mic
  7. Outdoor Security Mount

argus-2e-2.png.webp

  1. Reset Hole 
  2. Micro SD Card Slot
  3. Micro USB Port
  4. Speaker

Installation of Argus 2E

Mount the Camera to the Wall

Step 1. Rotate to separate the base from the security mount.

1._Rotate_the_base.png

Step 2. Drill holes with the mounting template and screw the base of the mount onto the wall. Then attach the other part of the mount to the base.

2._drill_hole_and_fix_the_mount.png

Step 3. Screw the camera to the mount. 

3._screw_camera.png

Step 4. Adjust the camera's angle to get the best field of view.

4._adjust_camera_view_angle.png

Step 5. Secure the camera by turning the part on the mount identified in the chart clockwise.

5._secure_camera.png

Note: To adjust the camera angle later, please loosen the mount by turning the upper part counterclockwise.

Install the Camera with Loop Strap

If you'd like to install the camera to a tree stem, follow up on the mounting method below.

Step 1. Thread the loop strap through the slot at the bottom of the security bracket.

1.thread_the_strap.png

Step 2. Fasten the strap around the tree tightly. 

secure_the_camera.png

Place the Camera on a Surface

If you plan to place the camera on a level surface indoors, for example, on the bookshelf, you could put the camera into the stand bracket and adjust the camera angle by slightly rotating the camera back and forth.

3.put_camera_on_stand.png

Note: To adjust the camera angle later, please loosen the mount by turning the upper part anticlockwise.

Micro SD Card Installation

Please refer to the instructions below to install the micro SD card for the camera.

1. Turn off the power switch before installing the micro SD card.

2.  Insert the micro SD card in to the micro SD card slot on the right side of the camera.
​sd_card_argus_2e.png

Note: Please use your fingernail (or use the provided reset needle) to push the micro SD card in until you feel that it's locked or you hear a "click".

3.  Turn on the power switch to power on the camera.

Installation Tips

Reolink battery-powered cameras like the Argus 2E use PIR motion sensor to detect motions. To make the PIR motion sensor work more precisely and to reduce false alerts, you may follow the tips below to install the camera.

Tip 1: Install cameras according to their viewing field

1. The viewing angle of Reolink Argus 2E is 120° diagonal. Please make sure that the monitoring area is well within its field of view.
2. The ideal viewing distance is 2-10 meters (7ft — 33ft), within which people will be recognized. To achieve a better viewing experience, it is not advised to place the camera too far away or too high (suggested mounting height: 2-3 meters) from the designated monitoring area.

installation_tips_1.jpg

Tip 2: Install cameras according to the detecting field of the PIR motion sensor

1. The detecting distance of PIR motion sensors is 9 meters, and the detecting angle is 120˚ horizontally. Motions out of this range can’t be detected.
2. Our PIR motion sensor is more sensitive to side-to-side movement than movement heading straight toward the camera.
For example, when a person moves straight toward the camera (shown below), the PIR motion sensor will be less sensitive to the movement.

installation_tips_2.jpg

For more details, please refer to:

Initial Setup

You may set up the camera on your wireless network via both Reolink App and Client. To do this, please refer to the articles below.

  • On Reolink App

    • Step 1. Download the App on your phone and start the setup process.
      Step 2. Tap on the "+" icon in the top right corner to start the initial setup.
      Step 3. Scan the QR code at the back of the camera or enter the 16-digit UID number to add it.
      Step 4. Select "Wi-Fi Not configured".
      Step 5. Enter the Wi-Fi password of the selected Wi-Fi network and tap Next.
      Step 6. Use the camera to scan the QR code generated on the phone.
      Step 7. After scanning, there will be a short beep sound. The camera will try to connect to the router.
      To get more information, please check: How to Initially Set up Reolink Battery-powered Cameras via Reolink App

  • On Reolink Client

    • Step 1. Download the Client on your PC and start the setup process.
      Step 2. Tap on the "+" icon in the top left corner to start the initial setup.
      Step 3. Enter the 16-digit UID number to add the camera.
      Step 4. Select "Connect to Wi-Fi".
      Step 5. Enter the Wi-Fi password of the selected Wi-Fi network and tap Next.
      Step 6. Use the camera to scan the QR code generated on the PC.
      Step 7. After scanning, there will be a short beep sound. The camera will try to connect to the router.
      For more details, please refer to: How to Initially Set up Battery-powered Cameras via Reolink Client (New Client)