Configuration - D400/B400

D400/B400 is an add-on camera that is recommended to connect to a Reolink PoE NVR. To better learn the working principle and settings of the camera, here are some instructions for your reference, including (note: You can click on the keywords below to jump to the corresponding section.)

Smart Person & Vehicle Detection
Detection Zone & Privacy Mask
Object Size

Smart Person & Vehicle Detection

Based on traditional Motion Detection, Smart Person & Vehicle Detection has optimized the algorithms and technology to massively reduce false alarms and filter Persons and Vehicles from all movements.

Note: Only D400/B400 with hardware version IPC_566B104MP support Smart Person & Vehicle Detection. (About how to find the hardware version of your camera, please refer to How to Find out System Information via Reolink PoE NVR or How to Find out System Information via Reolink PoE NVR ( New UI)

You can set it up via both Reolink App, Reolink Client, or the monitor.

On Reolink App
1. Please open your Reolink APP > Device settings > Camera Recording/Email Alerts/Push Notification > Schedule > Choose Person/Vehicle/Others.
  For example, if you only need to receive a push when a person is detected, please only choose Person here and do not choose Vehicle and Others.
2. For more details, please refer to:
  
  How to Set up Smart Vehicle Detection only via Reolink APP
  
  How to Set up Smart Person Detection only via Reolink APP
On Reolink Client
1. Please open your Reolink PC client > Device settings > Surveillance > Record, then click Schedule.
  Note: Make sure that the Enable Record button has been turned on.
2. Please click the detection type and then choose the time & date for detection.
  For example, if you need the camera to record only when a person is detected, please only click Person and unclick Vehicle and Others.
3. Finally, click the Save button at the bottom of the setting to save your settings.
4. For more details, please refer to:
  How to Set up Smart Person/Vehicle Detection via Reolink Client (New Client)
On the Monitor
1. Please Go to Survellience >Record/Email Schedule.
2. Please click the detection type and then choose the Time & Date for detection.
  For example, if you need the camera to record only when a person is detected, please only click Person and unclick Vehicle and Others.
3. Finally, click Apply to Other Cameras.
4. For more details, please refer to How to Set Smart Detection via the PoE NVR System (New UI) (Video)

Detection Zone & Privacy Mask

This part will guide you to distinguish the detection zone from the privacy mask and help you to set a detection zone or privacy mask.

Differences

Detection Zone: This function is used to reduce the false alarm. If you paint a non-detection area, the movements in the non-detection area will not trigger the camera to record or send a push, but the pictures in the non-detection area will still appear on the previewing page. The detection zone will not influence the previewing pictures.

Privacy Mask: This function is used to protect others' privacy in case some areas are not allowed to be monitored. You can add at most 3 privacy masks. Our privacy mask is a rectangle and you can not customize its shape. The privacy mask will influence the previewing pictures.

Set Up a Detection Zone
1. The following video will guide you to set up a detection zone via both Reolink App (from the beginning) and Reolink Client (from 2:15).
2. Note: The grey part is the non-detection area
Set Up a Privacy Mask
1. On Reolink App:
  Please open the Reolink App > Device Settings > Display > Privacy Mask.
  
  After settings up, the pictures covered by the privacy mask can not be previewed anymore.
2. On Reolink Client:
  Please open Reolink client > Device settings > Device > Display > Privacy Mask.
  
  After settings up, the pictures covered by the privacy mask can not be previewed anymore.
3. On the monitor:
  Please go to Camera > Display > Privacy Mask Settings (up to 4).
  
  Please remember to click "Apply" after setting up.

Object Size

Object Size is used to reduce false alarms.
The movements smaller than the minimum size will not be collected.
Vice versa, the movements larger than the maximum size will not be collected as well.

You can set it up via both Reolink App and Reolink Client.

On Reolink App
1. Please open your Reolink APP > Device settings > Detection Alarm > Object Size.
  
  Note: the movements larger than the blue rectangle will not trigger the alarm. The movements smaller than the orange rectangle will not trigger the alarm.
On Reolink Client
1. Please open Reolink Client > Device settings > Device > Motion Detection > Object Size.
  
  Note: the movements larger than the blue rectangle will not trigger an alarm. The movements smaller than the orange rectangle will not trigger the alarm.
On the Monitor
1. Please go to Cameras > Detection > Object Size.
  
  For more details, please refer to How to Set Smart Detection via the PoE NVR System (New UI) (Video)
  Note: If you create an objective size for Person Detection, this will not act on Vehicles and Pets.To know more devices settings information about the POE cameras, please refer to Device Settings for PoE cameras

Configuration - D400/B400

Smart Person & Vehicle Detection

On Reolink App

On Reolink Client

On the Monitor