If you have ordered the RLC-522 or if you are interested in this camera model, and want to get some basic information about this product before putting it in use or placing the order, you may refer to the below introduction.

This article includes the following 4 parts which will help you quickly understand the use and working principle of the camera:

Part 1: Unboxing Video 

Part 2: Product Overview

Part 3: Installation 

Part 4: Initial Setup

Unboxing Video of RLC-522 

If you just receive your new camera and are not familiar with the camera, you can have a look at the below video about the unboxing, setup, and installation of the camera.

Product Overview

You may find detailed information about the structure and components of the camera here.

overview-2.png

  1. Power
  2. Reset Button
  3. Network
  4. Waterproof Lid

overview-1.png

  1. Mount
  2. Metal Aluminum Case
  3. 18 IR LEDs
  4. High Definition Lens (f=2.7-12mm)
  5. Daylight Sensor
  6. Built-in Mic

overview-3.png

  1. SD card Slot

For more specs of the RLC-522 camera, please refer to Specifications

Installation of RLC-522

Connection Diagram

To make the camera work properly and monitor the designed area, you need to connect the camera to the network, and also mount the camera with a bracket as you need.

To get it connected, you need to use the PoE Switch (IEEE 802.3af, 48V Active) or DC Power (DC 12.0V⎓2A, <24W) to power it on first. You can refer to the diagram below to connect it to the network:
rlc-811a-3.png

If you want to make Reolink NVR work with the camera, then its connection diagram will be like below:

PoE NVR Connection

Mounting

Please refer to the following steps to install the camera with the mount.

Step 1. Use the mounting hole template to drill mounting holes on the ceiling and plant the rubber anchoring into the mounting holes.

Step 2. Screw the base panel to the mounting holes on the ceiling or wall.

It's suggested to install dome cameras on the ceiling usually.
822a-3.png

Step 3. Fit the concave at the bottom of the camera (marked as 4,5,6 in the picture below) to the convex on the base panel (marked as 1,2,3 in the picture below), and then rotate the camera seating (marked as Part A) clockwise to lock the camera tightly with the base panel.

Note: To take down the camera, please rotate part A anti-clockwise.
822a-4.png
822a-5.png
822a-6.png

Step 4. Once the camera is installed, you can adjust the angle up and down 70 degrees or 360 degrees horizontally.
822a-6.jpg

Installation Tips

  • Do not face the camera toward any light sources.
  • Do not point the camera toward a glass window. Otherwise, it may result in poor image performance due to the window glare from infrared LEDs, ambient lights or status lights.
  • Do not place the camera in a shaded area and point it towards a well-lit area. Otherwise, it may result in poor image performance. For better image quality, please make sure that the lighting condition for both the camera and the captured object is the same.
  • For better image quality, it is recommended that the lens be cleaned with a soft cloth regularly.
  • Make sure the power ports are not exposed to water or moisture or blocked by dirt or other elements.
  • Do not install the camera in places where rain and snow may hit the lens directly.
  • The camera may work in extremely cold conditions as low as -25°C as it will produce heat when powered on. You may power on the camera indoors for a few minutes before installing it outdoors.

Micro SD Card Installation

Please refer to the steps below to install the Micro SD card on your camera.

Step 1. Find the Micro SD card slot and unscrew the screws to open it.

Step 2. Insert the Micro SD card, please use your fingernail (or use a pen or a needle) to push the Micro SD card in until you feel it is locked, and you will hear a click sound and the Micro SD card will not pop out if the camera is inserted in properly.

Step 3. Screw the screws to close the cover tightly. 

rlc-822a-3.png.webp

Initial Setup

To set up the camera, you need to connect the camera to a PoE switch/injector for network connection. After that, you may finish the initial setup via both Reolink App and the Client.